FAQ - MRS Electronic

Filter

All questions

Frequently asked questions

After switching off Kl15 on the CAN I/O, the module remains active.

CAN I/O SPS Waterproof CAN I/O

The outputs do not supply voltage

M2600 ECO CAN PLC

Does the Micro PLC CAN LIN also have LIN wake-up?

Micro PLC CAN LIN

More questions …

What is the quiescent current of the Micro SPS CAN 4 I/O in sleep mode?

Micro PLC CAN 4 I/O

It seems after a test of the program, as if a signal does not come to the exit, although it was drawn in the graphic programming.

MRS Developers Studio

Where do I send my order?

Order processes

Is there a minimum order value when ordering?

Order processes

When opening the "MCU-Flasher" window, the message "CAN interface is already occupied by a program or not connected" appears even though the PEAK-USB adapter is connected

MRS Developers Studio

Where are the thresholds for the digital inputs?

General product questions

Do the modules also have an analog output?

General product questions

What is the pin assignment of a Sub-D 9pin connector with CAN cable?

General product questions

How to correctly install the terminating resistor of a CAN cable?

General product questions

Can the analog inputs be used in parallel as digital inputs?

General product questions

Can the outputs be switched to ground instead of supply voltage?

General product questions

After clicking on "Scan", the log window will say "SCAN COMPLETED", but no module found will be listed even though it is connected.

MRS Developers Studio

When reading out the module data, a timeout error occurs.

MRS Developers Studio

Changing the boot loader ID, module name or baud rate of the bootloader does not apply the changes, even though the changes were written without an error message.

MRS Developers Studio

Module is found during the scan, but when a program is ready to be flashed, in the log window only "MCU: Program Download" appears and the flash process does not start.

MRS Developers Studio

Which function block do I use for the motor controller 10 A CAN (PRO)?

Motor Controls 10A CAN Motorsteuerung 10A CAN PRO

Is the order version 1.300.300.00 - Do I have the function "CAN-Wake-up" on all 3 CAN interfaces?

M3600 CAN PLC

What is the function of the status LED?

M2600 ECO CAN PLC

Sleep mode does not work / module draws too much power in standby.

M2600 ECO CAN PLC

Which resistance values Pull Up and Pull Down are possible?

M2600 ECO CAN PLC

Is there a digital input to measure the frequency?

M2600 ECO CAN PLC

How can the duty cycle of a frequency be determined?

M2600 ECO CAN PLC

Can different PWM signals (for example 8 V, 6 V or 12 V) be processed with the M2600?

M2600 ECO CAN PLC

What function does the "IDENT" pin have?

M2600 ECO CAN PLC

Is the M2600 ECO CAN PLC capable of CAN wake-up?

M2600 ECO CAN PLC

How fast can the ADC converter process the analogue values and at what time interval are they available to the program?

M2600 ECO CAN PLC M3600 CAN PLC

On the CAN I/O WP PRO V2, the current output does not regulate properly.

CAN I/O Waterproof

Can the module be ordered as Master or Slave?

Micro PLC CAN LIN Micro SPS CAN LIN Micro Gateway

What is the quiescent current in sleep mode?

Micro PLC CAN LIN

Does the Micro PLC CAN LIN also have CAN wake-up?

Micro PLC CAN LIN

How can the analog input be switched from voltage to current?

Micro PLC CAN 4 ANA

Which minimum output voltage does the Micro PLC CAN 4 ANA provide?

Micro PLC CAN 4 ANA

Can the HSD outputs also be switched in parallel?

CAN I/O SPS Waterproof CAN I/O CAN I/O Waterproof Micro PLC CAN 4 I/O M2600 ECO CAN PLC M3600 CAN PLC CAN/RS485 Gateway CAN Gateway Module

What is the current consumption in sleep mode (F15 inactive)?

Universal Gateway 5x CAN

What is the quiescent current of the CAN relay box?

CAN Relay Box

Is the CAN relay box CAN wake-up capable?

CAN Relay Box

Is the load-side power supply running via KL30 or KL15?

CAN Gateway Module

Can the HSD outputs also measure the current?

CAN Gateway Module

Are the HSD outputs internally secured?

CAN Gateway Module

Can all four motors be controlled at the same time?

4-fold Motor Controller

Direction of rotation reversal does not work if a 1 or 0 is alternately applied to the "Direction" input.

Motor Controls 5A CAN Motor Controls 10A CAN Motorsteuerung 10A CAN PRO

Can the motor full bridge also be operated as a half bridge in parallel?

Motor Controls 5A CAN Motor Controls 10A CAN Motorsteuerung 10A CAN PRO

How do I put the module in Sleep_Mode?

Motor Controls 5A CAN Motor Controls 10A CAN

Can the frequency thresholds also be chosen freely?

Frequenzwächter 12 V Frequenzwächter 24 V Frequenzwächter 9-30 V

Can the voltage thresholds and the delay times also be chosen freely?

Spannungswächter 12V Spannungswächter 24V Spannungswächter 9 - 30 V

Which threshold values do the outputs have?

LED Universalblinkgeber 24 V Universal Flasher Universal Flasher LED

Do all four channels have to be occupied or is it sufficient to connect only the channels "left front" and "right front" with a sufficient load?

LED Universalblinkgeber 24 V Universal Flasher Universal Flasher LED

Can the customer reprogram the current thresholds at the universal flasher itself?

LED Universalblinkgeber 24 V Universal Flasher Universal Flasher LED

How fast is the switching time at the output from a trigger input?

Impulsrelais M3 24 V Impulsrelais M1 kompakt 12 V Impulsrelais M1 kompakt 24 V Impulsrelais einstellbar 12 V Impulsrelais einstellbar 24 V Pulse Relays M3

How can I program the Frequency CNT measurement in C code?

CAN I/O SPS Waterproof CAN I/O

Does the 5 VRef output have a stabilized voltage output or does it have a residual ripple?

CAN I/O CAN I/O Waterproof

How fast are the inputs on the CAN I/O?

CAN I/O SPS Waterproof CAN I/O CAN I/O Waterproof

Does the CAN I/O CAN-Wake-up?

CAN I/O SPS Waterproof CAN I/O

How can the PWM outputs on the M2600 ECO CAN PLC be activated?

M2600 ECO CAN PLC

Is there a terminating resistor on the CAN relay box?

CAN Relay Box

How can the 4-in1 motor control be programmed?

4-fold Motor Controller

What are the switching thresholds for a logical "1" or a logical "0" at the trigger input (for example, KL15)?

Time Relays Pulse Relays Blinkgeber

Is the Micro PLC CAN 4 I/O capable of CAN wake-up?

Micro PLC CAN 4 I/O

[Translate to Commonwealth English:] Können mit der CAN I/O WP PRO V2 auch Frequenzen gemessen werden?

CAN I/O Waterproof